- #Mariner 30 outboard manual install#
- #Mariner 30 outboard manual manual#
- #Mariner 30 outboard manual full#
- #Mariner 30 outboard manual code#
- #Mariner 30 outboard manual free#
#Mariner 30 outboard manual install#
Install oil level plug before removing oil filler tube from drain hole.ĭo not re-use gaskets once removed. oz) Recommended oil : Outboard Motor Gear Oil or SAE #90 Hypoid gear oil.ĥ. Fill with recommended gear oil through oil drain hole until oil just starts to flow out from oil level hole. Remove lower gear oil drain plug before gear oil level plug and drain gear oil.Ĥ. two minutes, then recheck engine oil level.ģ.
#Mariner 30 outboard manual manual#
Refer to the MerCruiser Repair Manual as procedures can differ depending on model and year. Start engine and allow it to run for several minutes at idle speed. (4) Turn ignition key to “OFF” position, then set emergency stop switch plate 1 in original position.ĩ. A short beep will be heard if cancellation is successfully finished. (3) Pull up emergency stop switch knob 2 three times in seven seconds. (2) Pull out emergency stop switch plate 1. To reset oil change reminder system’s operation time to zero (cancellation) Oil filter change : 5.7 L (6.0 / 5.0 US / Imp. Oil change only : 5.5 L (5.8 / 4.8 US / Imp. Pour recommended engine oil into oil filler opening, then install oil filler cap. Tighten engine oil drain plug to specified torque.ħ. (4) Tighten filter 3/4 turn from point of contact with mounting surface using an oil filter wrench.Ħ. (3) Screw new filter on by hand until filter O-ring contacts the mounting surface. (2) Using oil filter wrench to loosen the oil filter, then remove filter and O-ring. NOTE: Before fitting new oil filter, be sure to oil O-ring. NOTE: For engine oil change only, go to step 6. Remove engine oil drain plug and gasket to drain engine oil. Place a container under engine oil drain plug.Ĥ. Place outboard motor upright on a level surface.ģ.
#Mariner 30 outboard manual full#
If level is low, add recommended oil to full level hole (Max.).
![mariner 30 outboard manual mariner 30 outboard manual](https://cdn2.bigcommerce.com/server2800/twxpu5v/product_images/uploaded_images/recoil.jpg)
Oil level should be between full level hole (Max.) and low level hole (Min.). Insert it fully into dipstick hole, then remove it to check oil level.ĥ. Remove oil level dipstick and wipe it clean.Ĥ. Place mercury 40hp manual outboard motor upright on a level surface.ģ. NOTE: More frequent servicing should be performed on outboard motors that are used under severe conditions.ġ. Maintenance intervals should be judged by number of hours or months, whichever comes first. The chart below lists the recommended intervals for all the required periodic service work necessary to keep the motor operating at peak performance and economy. PRE-PROGRAMMED VALUE FOR FAIL-SAFE SYSTEMįUEL VAPOR SEPARATOR / HIGH PRESSURE FUEL PUMP
#Mariner 30 outboard manual code#
Information on this page has come from multiple third parties and can not be guaranteed to be accurate.PRIORITY / CODE / PATTERN FOR SELF-DIAGNOSTICĬONDITION FOR SELF-DIAGNOSTIC SYSTEM OPERATION
![mariner 30 outboard manual mariner 30 outboard manual](https://images-na.ssl-images-amazon.com/images/I/51Aawvr0GyL._SX258_BO1,204,203,200_.jpg)
The iboats Forum Directory can likely help you find a lot of outboard information as it is arranged by subject. The iboats Outboard Motor Forums are another excellent source of information. Thus, for safety and other reasons, it is a good idea to verify information here to Even if this information is the same as the original factory specs,īoats are sometimes modified. Many sources we can not guarantee its accuracy.
#Mariner 30 outboard manual free#
Information on this page is provided to you as a free service of. Be sure to do your testing under your normal boating conditions and with a good propeller (not bent, cracked, or excessively chipped). You want your RPM's to be within the proper range while at wide open throttle (WOT).
![mariner 30 outboard manual mariner 30 outboard manual](https://cdn.shopify.com/s/files/1/1095/2674/products/P5248615_1024x1024.jpg)
For example, if you look at your tachometer at top speed and it is not within the engine's RPM range then that is generally not good. Your engine's RPM range is important in choosing the right propeller for a given application. This outboard has starter of the electric type and power steering as well. The bore and stroke are 2.83" and 2.40" respectively. Mariner by Mercury Marine outboard motor was made for the saltwater environment.